Alley Bumps

Alley bumps were developed to address speeding and cut-through traffic specifically in alleyways. Molded bright reflective tape and high-quality cat?s-eye reflectors alert drivers well in advance. Channeled bottom facilitates cables and drainage. Available in 4? and 6? lengths, along with end caps to protect the alley bump ends and motorists. Alley bumps are designed for speeds of 1-5 mph.

printer friendly

Product Name:

Rubber Speed Bumps 3” thick

Models:

6’, 4’ long

Product description:

Material: compression molded composite: 100% recycled rubber and polyurethane prepolymer

Physical properties of the rubber composite:

a.	Density	0.6 oz/cu in	(ASTM C642)
b.	Durometer Hardness	70A ± 7	(ASTM D2240)
c.	Tensile Strength	300 psi	(ASTM D412)
d.	Compression deformation	7% at 70psi, 68°F	(ASTM D575)
e.	Brittleness at Low temperature:	-40°F	(ASTM D746)
f.	Freeze and thaw when exposed to deicing chemicals	no loss after 50 cycles	(ASTM C672)
g.	Coefficient of thermal expansion:	8 x10-5 in/in/°F	(ASTM C531)
h.	Weathering 70 hours at 158°F		(ASTM D573)

- hardness retained 100% (± 5%)
- compressive strength 100% (± 5%)
- tensile strength 100% (± 5%)
- elongation retained 100% (± 5%)

3.	Available models: 6’, 4’ long
4.	Basic dimensions and nominal weights as per attached drawing for 6’ model
5.	Finishing: Black recycled rubber composite with yellow, durable and reflective, preformed pavement marking tape (ASTM D4061) 6” wide, covered with glass beads, as per attached drawing

Installation method:

installation with rebar spikes 14” long
(minimum diameter ½”)

- 4 spikes for 6’ model
- 3 spikes for 4’ model

Components:

a)	100% recycled rubber from car and truck tires (NR, SBR)
b)	polyurethane prepolymer
c)	cat’s eyes reflectors
d)	yellow, durable and reflective preformed pavement marking tape as per ASTM D4061, covered with the glass beads
e)	molded in steel washers

Attached Drawings:

6’ model, drawing No. 6SB10
14” rebar spike, drawing No. 05SP01



	Rubber- Traffic Logix Alley Bumps are made from recycled rubber tires. Rubber is lighter and easier to work with than asphalt and concrete, significantly minimizing the number of hours that need to be invested to install the solutions. Rubber pieces can be pulled up and moved without being destroyed. This is convenient for municipalities that want to institute temporary measures to test an area and is also a safety measure so that products can be stored during the winter to prevent snow plow damage. Unlike concrete and asphalt which necessitate frequent and high cost replacement, rubber products are long lasting and cost-efficient. In addition to long term benefits, rubber products offer a quick, easy way to install solutions when timing is key.

	Easy installation- Traffic Logix Alley Bumps are simple to install. They are secured into asphalt with spikes or into concrete with lag bolts and shields. They do not require skilled labor to install.

	Molded Reflective Tape- Traffic Logix speed bumps are embedded with highly reflective tape. This tape is a safety feature to ensure that drivers can clearly see the panel both during the daytime and at night. Traffic Logix uses this tape on its products instead of paint since paint often fades away within months and the reflective tape can last for several years. Tape is available in several color choices. Highly reflective cat's eyes can be installed on any device for further enhanced visibility.

	Environmentally Friendly Design- Traffic Logix Alley Bumps are made from recycled rubber tires. This ensures that while products address community health and safety needs, they are also friendly to the environment. An additional benefit of the product’s green design is that it can help municipalities obtain funding for the products since many areas have a budget allocation for recycled products.

	Hear what our customers have to say about our products.