|
|
 |
| Private Communities«Speed Bumps |
| |
|
|
|
| The Easy Rider speed bump reduces vehicle speeds to 2-5 mph. Molded bright reflective tape as well as high-quality cat?s-eye reflectors alert drivers well in advance. Channeled bottom facilitates cables and drainage. Easy Rider is available in 4? and 6? lengths, along with end caps to protect the speed bump ends and motorists. |
|
|
|
|
|
      |
|
|
| |
 |
Easy Rider Speed Bump
Dimensions: |
| 4' or 6' X 12" X 2 ¼" |
| 32 lb. (4'), 51 lb. (6') |
|
Easy Rider End Cap:
Dimensions: |
| 6" X 12" X 2 ¼" |
| 5.5 lb. |
|
| |
| |
|
| |
| Traffic Logix solutions have been installed in hundreds of locations across North America. |
|
|
|
|
|
|
 printer friendly |
| Product Name: |
Rubber Speed Bumps 2.25” thick |
|
|
| |
|
| Models: |
6’, 4’ long |
|
|
| |
|
Product description: |
| 1. |
Material: compression molded composite: 100% recycled
rubber and polyurethane prepolymer |
| 2. |
Physical properties of the rubber composite: |
| a. |
Density |
0.6 oz/cu in |
(ASTM C642) |
| b. |
Durometer Hardness |
70A ± 7 |
(ASTM D2240) |
| c. |
Tensile Strength |
300 psi |
(ASTM D412) |
| d. |
Compression deformation |
7% at 70psi, 68°F |
(ASTM D575) |
| e. |
Brittleness at Low temperature: |
-40°F |
(ASTM D746) |
| f. |
Freeze and thaw when exposed
to deicing chemicals |
no loss after 50 cycles |
(ASTM C672) |
| g. |
Coefficient of thermal expansion: |
8 x10-5 in/in/°F |
(ASTM C531) |
| h. |
Weathering 70 hours at 158°F |
|
(ASTM D573) |
|
|
|
- hardness retained 100% (± 5%)
- compressive strength 100% (± 5%)
- tensile strength 100% (± 5%)
- elongation retained 100% (± 5%) |
| |
| 3. |
Available models: 6’, 4’ long |
| 4. |
Basic dimensions and nominal weights as per attached drawing for 6’
model |
| 5. |
Finishing: Black recycled rubber composite with yellow, durable and
reflective, preformed pavement marking tape (ASTM D4061)
6” wide, covered with glass beads, as per attached drawing |
|
|
|
|
|
Installation method: |
installation with rebar spikes 14” long
(minimum diameter ½”)
- 4 spikes for 6’ model
- 3 spikes for 4’ model
|
|
|
|
|
|
Components: |
a) |
100% recycled rubber from car and truck tires (NR, SBR) |
b) |
polyurethane prepolymer |
c) |
cat’s eyes reflectors |
| d) |
yellow, durable and reflective preformed pavement marking tape as per
ASTM D4061, covered with the glass beads |
| e) |
molded in steel washers |
|
|
|
|
|
Attached Drawings: |
6’ model, drawing No. 6SB01-1
14” rebar spike, drawing No. 05SP01 |
| |
 |
|
|
|
|
|
| |
 |
| |
Installation of Easy Rider speed bumps with spikes
(Recommended for asphalt surfaces):
- Drill 1/2” diameter holes in the asphalt through the product’s holes
- Drive 1/2” rebar spike (14” long) through the holes in the product
Installation of Easy Rider speed bumps with lag bolts and metal shields (Recommended for concrete surfaces):
- Use 1/2” or 5/8 lag bolts (5.5” long)
- Drill 1/2” dia. pilot holes through the product’s installation holes
- Remove the product; re-drill the holes for the diameter and depth required by the metal shields
- Install the metal shields, re-position the product and bolt with lag bolts
|
|
|
|
|
|
|
Rubber- Traffic Logix Speed Bumps are made from recycled rubber tires. Rubber is lighter and easier to work with than asphalt and concrete, significantly minimizing the number of hours that need to be invested to install the solutions. Rubber pieces can be pulled up and moved without being destroyed. This is convenient for municipalities that want to institute temporary measures to test an area and is also a safety measure so that products can be stored during the winter to prevent snow plow damage. Unlike concrete and asphalt which necessitate frequent and high cost replacement, rubber products are long lasting and cost-efficient. In addition to long term benefits, rubber products offer a quick, easy way to install solutions when timing is key. |
| |
|
|
Easy installation- Traffic Logix Easy Rider Speed Bumps are simple to install. They are secured into asphalt with spikes or into concrete with lag bolts and shields. They do not require skilled labor to install. |
| |
|
|
Molded Reflective Tape- The Traffic Logix speed bumps are embedded with highly reflective tape. This tape is a safety feature to ensure that drivers can clearly see the panel both during the daytime and at night. Traffic Logix uses this tape on its products instead of paint since paint often fades away within months and the reflective tape can last for several years. Highly reflective cat's eyes can be installed on any device for further enhanced visibility. |
| |
|
|
Environmentally Friendly Design- Traffic Logix Speed Bumps are made from recycled rubber tires. This ensures that while products address community health and safety needs, they are also friendly to the environment. An additional benefit of the product’s green design is that it can help municipalities obtain funding for the products since many areas have a budget allocation for recycled products. |
| |
|
| |
 Hear what our customers have to say about our products. |
|
|
|
|
|
|
 |
How to get Traffic Calming on Your Streets
--
December 06 2007
A step by step guide to help residents through the process of slowing traffic on your roads.
|
 |
Why More and More Cities are Choosing to Use Rubber Solutions Permanently
--
November 07 2007
In the past several years, rubber traffic calming solutions have been rapidly growing in popularity in the US. While initially viewed as a way to test streets before installing asphalt devices, rubber products are being used as a permanent solution to speeding traffic.
|
 |
Choosing the Right Device
--
July 07 2007
A short guide to traffic calming measures and their uses. Provides usage and application information for speed bumps, humps, tables, cushions, and traffic circles.
|
|
|
|
|
|
| |
| |
| . |
|
|
